![]() |
The
Living History Engineer's Gun Drill |
| 1. Broadside Carriage Guns | |
![]() |
These guns like the others to be discussed here are designated by the weight of the solid ball ammunition used. For example: if the ball weighs six pounds, the gun is designated as a 6 pdr.--nine pounds—9 pdr. and so on through 12 pdrs, 18 pdrs, 24 pdrs and 32 pdrs. There was also a 36 pdr. used in the French naval service. The largest guns of this period were the 42 pdrs found in coastal fortifications and in some major warships. The six to twenty-four pound gun was in common use depending upon the size of the vessel and the 24 pdr. broadside gun and the 32 pdr. Carronade are what we will deal with in discussing the broadside action. The broadside guns were manufactured in three lengths; short, medium, and long; the long guns being the most accurate and long ranging. Long guns were sought out and used primarily for warships, while the short and medium guns were used for privateers and merchant vessels that routinely ventured into pirate waters like the British East and West Indiamen. These ships carried extremely valuable cargoes and needed significant armament to pass safely through the Eastern Seas. The Short and Medium barreled weapons were often referred to as "Cannonades" and had a tendency to "jump" upon firing when they were hot, after a few rounds had been put through them. These above weapons were all mounted on typical wheeled sea carriages whose design adapted the gun very well to the ship's structure. The gun had two projections, from the barrel, about midway between the muzzle and the breech of the gun, one on each side of the barrel, which were called "trunnions." These trunnions fitted into half holes cut into the top of the carriage, which carried the immediate weight of the barrel. When the gun was "seated" in the carriage, the trunnions were fitted into the half holes or "trunnion slots." The trunnions were then covered over the top half of the trunnion with a "cap screw" which effectively locked the gun into the carriage. This capscrew still allowed the gun to be elevated or depressed for the purpose of ranging. Training the gun as well as moving the entire gun and carriage had to be done by handspike. |
| 2. Chase Guns | |
|
These guns, as the name implies, were used in the chase of another
vessel or when being chased, in turn, and the best of these were either
9 pdrs, on smaller vessels or 18 pdrs on larger warships. These
weapons were usually precision bored, and were always "long"
guns. They were as accurate a gun as was available in the period.
They were mounted in the bows and the stern of a ship, and were mounted
on sea carriages, as with broadside guns. Both Chase Guns and
Broadside Guns were counted in the calculation of the ships
"rate" and the weight of her broadside. The U.S. ships
of the period were very similar in "rate" to the British
vessels as indicated below. For example: |
|
| 3. Carronades | |
| These guns were called "Smashers" and they were developed very late in the Revolutionary War period at a foundry in Carron Scotland, hence the name. They were a short-range gun. However they could deliver a heavy ball for the weight of the barrel. The gun rested on a slide carriage and was mounted with a "mounting block" cast on the bottom of the gun instead of trunnions. The barrel was very light in comparison to a long gun and could do significant damage at short range. They were cast in 9 pdr., 12 pdr., 18 pdr., and 32 pdr. weapons and did not count in the ships rate. However, virtually every warship in the Spanish, Dutch, British, French and American navies carried them. There was also a variation of the Carronade called the "Gunade" which was a very similar gun except it was mounted on a sea carriage instead of a slide carriage and used trunnions instead of the mounting block. The "Gunade" was almost totally confined to merchant ships and privateers. Another advantage of the Carronade / Gunade was that it required a much smaller crew. | |
![]() |
|
| For the purposes of this treatise we will not deal with ordnance from the "monkeytail" swivel up to the 6pdr long gun. Nor will we deal with the Naval Mortar, which was often a valuable addition to a single ship, or a specially designed "mortar-ship" to a fleet charged with special duties. These are smaller and more specialized ordnance and had a variety of uses aboard ship. They can be dealt with in another discussion. While in the next section we will discuss gun crew action, we will consider the 24 pdr. Broadside Long Gun and the 32 pdr. Carronade only. It will be understood that the smaller guns did not need the large crews due to the weight of the gun, primarily. However, a description of the duties of each of the gun crews will serve to familiarize you with the many considerations in firing and preparing to fire warship's guns of this period. | |
| 4. Crew Stations | |
|
Draw two lines across the page about 1/4 of an inch apart leaving some
space for writing above the lines and about 10 times that much space
below the lines. In the
vertical center of the page, at right angles to the double lines draw a
cannon barrel that extends about halfway through both of the parallel
lines with the muzzle pointing at the top of the page. The two
parallel lines are the ship's bulwark or side, and the cannon barrel
represents one gun. Label between the parallel lines "ship's
bulwark" and label the gun barrel "long 24 pound gun." |
|
![]() |
|
|
Under "Position and Duty At Gun", beneath the bulwark lines,
make the following vertical list of positions and mark each position
beginning with a dot, thusly: •1st Sponger & Rammer & Side Tackle (S.T.), Just to the right of this list and under the heading "When Called
Away" beneath the bulwark double lines write down the below
positions, matching the top position with the top position in the
"Position and Duty At Gun" column. •2nd Boarder; The above lists indicate the required gun crew for a 24-pound long gun.
Obviously a 12-pound gun would not require such a large crew.
The side columns indicate the additional positions for gun
crewmembers should the Captain call for boarders or for a fire team.
Using the right hand columns as an example let us now move to the
left side of the gun barrel and under the title of the column above the
bulwark lines, "Position and Duty At Gun" below the bulwarks
lines let us put down the following list: •1st Loader and S.T.; Directly behind the cannon barrel cascabel at a safe distance place the
following; •Powder Boy. To the left of the above list and the vertical line separating the
columns under the title "When Called Away" and beneath the
double bulwark lines write the following list of positions matching the
top position with the top position of the above list: •2nd Boarder; |
|
![]() |
|
![]() |
|
|
To better understand the handling of guns, the men employed and the
instruments used, let me quote the manual exercise: 1."Silence! Man
the Starboard (or Port) guns!" At this preparatory order the strictest silence is to be observed.
The Gun Captain faces the gun muzzle; the men on the right and
left stand facing the gun; all fix
thier eyes on the Captain and attentively wait for orders. 2."Cast Loose and Provide!" The Gun Captain commands, sees his gun cleared and cast loose, portlid
unbarred ready for tricing up, or half ports taken out*, side and train
tackles hooked to the side training bolts, and the train-tackle to the
eyebolt in the rear of the gun; casts loose and middles breaching and
places selvage straps and toggles amidships; takes off the lock cover,
hands it to the train tackleman, who places it amidships; buckles on his
waist belt; (with a frog for a pistol, and with it cartridges and
percussion caps and a box containing fifty primers, fitted to a slip on
the waist belt), provides himself with a priming wire (vent pricker),
puts on a secures his thumb stall; sees that the gear and implements for
the service of the gun are all in place and ready for use, and that the
men are properly equipped *usually
upper deck guns have two-piece portlids and lower deck guns have one
piece portlids Second Gun Captain assists in casting loose and middling breeching;
takes off and places amidships sight covers, selvage straps, and
toggles; handles quoin; provides thumb-stalls*, priming wires, and
boring bitt (vent auger), linstock (properly armed with slow match and
lit) and equips himself with
the first two; clears the lock string, and lays it in a loose coil round
the lock, convenient for use, and buckles on his waist belt, furnished
the same as the First Captain's. If
the gun is furnished with an elevating screw, elevates the gun that the
lower half port may be let down. *thumbstall--a
leather thumb protector to cover the thumb when when sealing the
touchhole on a hot gun
First Loader, aided by the First Sponger, casts loose port-lanyard,
removes upper half port and passes it to the men on the left side of the
gun, who lay it amidships, lets down the half port.
On the lower deck, he casts off port lanyards and mizzen
lashings; removes the port bar and passes it to the men at the left side
of the gun, who lays it amidships; bears out (opens) port.
On all decks, places handswabs and chocking-quoin near the ship's
sides on the left side of the gun, aids First Sponger in taking the
tompion out of the muzzle of the gun. Second Loader aids in casting loose; sees the wads in place, and for
rifled cannon places a pot of grease at hand; hooks outer block of side
tackle to side training bolt, on the left side of the gun. First Sponger casts loose port-lanyards and aids First Loader in
removing upper half port and letting down lower ones, and on lower
decks, in removing port bar, bearing out the port and taking off the
muzzle lashings; takes out the tompion and passes it to the Second
Sponger, who hangs it amidships; places chocking quoin on the right side
of the gun near the ship's side. Second Sponger assists in casting loose, hooks outer blocks of
sidetackle to side training bolt on the right side of the gun. The Spongers take down the sponges and rammers, take off the sponge cap
and hang it out of the way; place sponges and rammers together on the
right side of the gun; heads toward the breach in the brackets overhead
on covered decks, other wise on deck. The Side Tacklemen assist in casting loose; on the lower decks, aid
port-tacklemen. moisten the sponge, being certain that the end of the
sponge which touches the bottom of the bore is thoroughly wet. Shellmen (Shot and Wad) assist in casting loose, provide shot and wads,
and proceed to the hatchway, ready to pass loaded shell*; if ordered. *Shell--See
under shot below Train Tacklemen lead out and hook train tackle. Handspikemen take out the handspikes on their respective sides, and with
gun carriages using a quoin, each standing between his handspike and the
side of the ship, place the heel of their handspikes on the steps of the
carriage and under the breech of the gun, and raise it so that the quoin
may be eased and the lower half port be let down; or when housed the bed
and quoin be adjusted. Then,
each Handspikeman will lay his handspike on deck, on his own side of the
gun, parallel with its axis, clear of the trucks and butt to the rear. Powder Boy repairs to his proper scuttle for his passing box, which
having received he returns and stands a little to the left and in rear
of the gun; keeping the passing box, under his left arm, and the cover
closely pressed down with his right hand.
In the passing box is the gunpowder cartridge. When there are
fourteen or more men at a gun, the Port Tackleman and Side Tacklemen, on
lower decks, lead out port tackle falls and assist in tricing up port,
and when high enough, belay the fall. NOTE-----Of course, a 12-pound gun would not have this number of men,
but the foregoing will illustrate the work that had to be done.
A long 12-pounder's crew would have consisted of eight men and a
boy, and a long six pounder, six men and a boy. When the guns (12 pdrs) on both side of the ship were manned
simultaneously, the First Captain, Loader, Sponger and Handspikeman man
the Starboard guns, and the Second Captain, Loader, Sponger and
Handspikeman the port guns, four men to a gun.
When only one side is in use, all eight men man the gun. In Loading the Gun, when it is run in as far as the breeching will
permit, its muzzle is only eighteen inches inboard, so the Sponger has
to lean out of the port to insert and manipulate the long handle of the
Sponge. 3. "Sponge Your Guns!" The First Sponger rams the wet sponge down the barrel to the breech
wetting the barrel, and the Captain places his thumb over the touchole
of the gun, while the sponge is removed smartly thus creating a vacuum
in the gun, extinguishing any sparks left in the gun from a previous
shot. Obviously, this step
is omitted at the first firing of the gun, and is very important
following the gun's firing. 3. "Load Cartridge!" The Powder Boy passes the powder charge from his passing box to the
First Loader, who places the powder charge (sewn up in a surge cartridge
bag) into the gun. 4. "Ram Cartridge!" The First Rammer rams the charge home to the Breech end of the cannon
barrel. 5. "Load Round (Ball or Shell)!" First Shot and Wad Man passes the selected round and wad to the First
Loader, who places the round and wad in the gun barrel.
The wad is placed between the cartridge and the round. 6. "Ram Round!" First Rammer rams the Round and Wad against the charge (cartridge).
The Gun Captain inserts the Priming Wire into the touchhole
making a hole in the Cartridge Bag, he then primes the gun either by
inserting a friction primer into the touchhole or by filling the touch
hole with Priming Powder from the Priming Horn at the gun. 7. "Run Out" At the Command from the Captain to "Run Out the Guns" the Side
Tacklemen run the guns up to the side of the ship, and the Gun Captain
sights the gun, elevating or depressing the gun barrel by use of the
quoin or an elevating screw. In
the case of the quoin, the Handspikemen eased (lift) the Breech of the
gun to allow proper placement of the Quoin. Training tackles and
handspike were also used to train the gun from side to side.
This action was not often needed since usually the guns fired
directly athwartships (broadside, hence the name), but in a chase
situation, for instance, the guns might be trained as far forward as
possible to get in a broadside shot without veering too far off course.
The same could be said for being chased and the guns trained aft.
This of course, depending upon the direction that the wind came
from. 8. "Fire As Your Guns Bear!" At this command the guns were fired.
The gun Captain warned his crew to "Clear The Gun"
meaning that they should stand clear, and fired the gun either by
touching the smoldering linstock to the fine priming gun powder in the
touchhole, igniting the friction primer by jerking the lanyard attached
to it, or by activating the firing lock (similar to a flintlock)
attached to the gun barrel. Generally,
lock firing did not do well until the gun was hot, and the linstock and
powder train was used at first. This action was determined by several possible additional commands as
determined by the ship's captain. If he wished to disable the opponent,
he would have instructed the Gun Captains to fire on an uproll to
disable the rigging. In this case he would have instructed that the guns
be loaded with grape or chain shot.
If the intention was to sink the opponent the guns would have
been loaded with solid shot and the gunners instructed to fire on the
down roll in order to hull the opponent. Shot / Rounds (type of); Solid shot determined the class of Gun, as a 24-pound cast iron ball was
fired from a 24 pounder cannon. Solid
shot were cast iron and were as the name implies solid. Grape was a round with 9 small iron balls on a wooden form wrapped in
canvas (This resembled a cluster of grapes, hence the name).
When fired the canvas disintegrated and the balls were like a
shotgun charge. This is very
different from canister, which has many more small iron balls packed in
a cloth, leather or tin container with sawdust and is used against
personnel. Chain shot was issued in a variety of forms: --a bag containing an iron
ring to which were fasted five 3 to 4 foot lengths of chain,
This was usually known as "star shot;" All of these rounds including grape were used to shred rigging.
The solid shot was used to dismount enemy guns, and penetrate the
enemy hull. Shell was a hollow cast iron sphere filled with gunpowder and separately
fused. It was tricky to use
since the shell fuse was ignited by the fire wash around the shell when
fired. If the shell was
"short-fused" or the fuse was faulty, and the round exploded
in the barrel, it usually damaged the gun severely and often the crew as
well. As to the command structure for firing the guns, the Gun Captains were
experienced seamen but were for the most part not petty officers.
For each "battery" of four guns there was usually a
Midshipman, or if not a Midshipman, a Gunner's Mate who was in charge of
the battery. His
responsibility was to see that all the equipment for the gun was in it's
place and well cared for, and his battle station was behind his guns for
which he was responsible. He
passed the word from the captain as to what rounds to load, where the
target was, and other information vital to the Gun Captains. |
|
| References: "American Sailing Ships--Thier Plans and History," Charles G. Davis, Dover Publications, New York, 1984; |
|